|
|
|
|
|
1. PRODUCT NAME
TEX•COTE® Multi-Texture/Color (MT/C) Wall Coating System2. MANUFACTURER
Textured Coatings of America, Inc.
Western Plant
5950 South Avalon Boulevard
Los Angeles, CA 90003-1384
PHONE: (323) 233-3111
Fax: (323) 232-1071Textured Coatings of America, Inc.
Corporate Headquarters and Eastern Plant
2422 East 15th Street
Panama City, FL 32405-6348
PHONE: (850) 769-0347
Fax: (850) 769-8339
Toll Free: (800) 454-0340Textured Coatings of America, Inc.
Sales Office
4101 Ravenswood Rd., Ste. 105A
Ft. Lauderdale, FL 33312-5371
PHONE: (954) 581-0771
Fax: (954) 581-95163. PRODUCT DESCRIPTION
Basic Use: Pigmented, textured interior/exterior seamless wall finish. For use on a wide range of wall surfaces, such as drywall, concrete, concrete block, brick, stucco, wood, glass, plaster, metal, and plastic. Excellent as a "camouflage" coating over existing blemished surfaces.Designed for spray application, a variety of textures is possible; fine, medium, or heavy splatter; medium or heavy lace; bark; cypress; and other special textures.
Durable, flexible, odorless, and has rapid drying properties with long term adhesion qualities. Excellent breathability. Fungus and mildew resistant.
An environmentally safe coating system, fully compliant with all existing Volatile Organic Contents (V.O.C.) regulations.
Composition and Materials: Combination of a water-based urethane and 100% acrylic-based terpolymer with elastomeric properties. Coating system consists of a MT/C Base Coat and MT/C Finish Coat over properly primed substrates.
Limitations: Do not apply TEX•COTE® Multi-Texture/Color until the following conditions are satisfied:
Quantities and Colors:
- Temperature within 45°F to 100°F range.
- Rain not imminent. Surfaces not damp or frozen.
- For above ground use only.
- All surface contaminants, that could be deleterious to coating performance, removed. - TSP or equivalent cleaning solution, followed by thorough rinsing. - Mildew, fungus, and algae neutralized.
- Joint sealants compatible with coating system, and cured per manufacturer's specifications before application.
- Primers exposed to UV rays more than 4 weeks prior to coating application must be re-primed.
- Coating materials agitated thoroughly prior to use.
- Maximum 12 month shelf life. Storage and handling pursuant to manufacturer published instructions.
Container Sizes: 1 gallon and 5 gallon pails.
Colors: Range of standard colors; custom colors available.4. TECHNICAL DATA
TEX•COTE® Multi-Texture/Color (MT/C) Wall Coating System passes Federal Test TTC-555b test criteria and performs well for a variety of other testing procedures (i.e. NFPA, ASTM) as shown on the accompanying table.PHYSICAL CONSTANTS OF MT/C BASE COAT:
Latex System Urethane Acrylic Based Weight Per Gallon 12.2 lbs. typical V.O.C. (GMS/liter minus water) 74.4 typical Volume Solids 55.89%PHYSICAL CONSTANTS OF MT/C FINISH COAT:
Latex System Acrylic Based Weight Per Gallon 10.0 lbs. typical V.O.C. (GMS/liter minus water) 162.5 Volume Solids 51.80%TEST DATA TEX•COTE® Multi-Texture/Color SYSTEM
1. Fire ASTM E-84 Class A Flame Spread 5 Smoke Developed 5 NFPA Class A UBC Class 1 2. Water Vapor Permeability ASTM E 96 (Procedure A) 13.35 (Perm. In.) ASTM D 1653 17.40 (Perm. In.) 3. Mildew Fungus Resistance ASTM D 3273 (TTP 29) No Disfigurement ASTM G21-90 (without clear glaze) 0 Growth ASTM G21-90 (with clear glaze) 0 Growth 4. Stain Resistance Modified ANSI A 118.6-85 No Visible Stains ASTM 1308-87 No Visible Staining from mild acids, chemicals, oils, food 5. Flexibility ASTM 522-89 Mandrel No Cracking 6. Scrub Resistance ASTM 2486-89 (without clear glaze) Pass 9,000 cycles ASTM 2486-89 (with clear glaze) Pass 11,000 cycles 7. Abrasion Resistance ASTM 986 Pass 1,000 cycles 8. Impact Resistance Type D Durometer 40ADDITIONAL TEST ON MT/C FINISH COAT:1. Twin ARC Weatherometer (Hours) 5,000 Hours 2. Federal Test TTC-555b Passes 3. Wind Driven Rain Test (98 MPH/24 Hours) Passes 4. Salt Spray Test ASTM B-117-64 300 Hours 5. Alkali Resistance GSA Exception #1 to TTC-555b Passes5. INSTALLATION
Application Equipment: Suitable spray equipment for the base and finish coats. Base coat, only, may be roller coated. Special texturing utilizes equipment recommended by manufacturer.Surface Preparation: Remove all surface contaminants, including dust, dirt, mildew, form oils, laitance, and other potential bond breakers. Removal means may include sandblasting, waterblasting, electric sanding, or wire brushing, pursuant to manufacturer's recommendations.
Fill large cracks, holes, or voids with an appropriate patching compound, texturing to match adjacent surface. For cracks between 1/16" - 1/8" in width, cut out and fill with recommended patching compound.
Recommended Primers: Dependent upon substrate and exposure (interior or exterior); refer to chart.
All primers must cure pursuant to manufacturer's instructions under acceptable environmental conditions prior to coating system application.
RECOMMENDED SUBSTRATES/PRIMERS (Interior):
SUBSTRATE PRIMER Drywall No Primer Required Concrete No Primer Required Cement Plaster No Primer Required Plastic (except polyethylene or polypropylene) No Primer Required Glass No Primer Required Brick No Primer Required Concrete Block TEX•COTE® Block Filler Wood/Particle Board Primer 62 Ceramic Tile X-100 19C Glazed Block X-100 19C or X-100 EpoxyRECOMMENDED SUBSTRATES/PRIMERS (Exterior):
SUBSTRATE PRIMER Concrete (Uncured, Bare) XL-70® Cement Plaster XL-70® Block System (new) XL-70® Slush•Cote, 1098D or TEX•COTE® Latex Block Filler Masonry (Painted) No. 62 Brick (Bare) XL-70® Cement Fibre Board No. 62 Galvanized Steel* No. 101 Aluminum No. 101 Ferrous Steel Zinc Chromate Copper X-100 Epoxy* If new refer to TEX•COTE® Reditex data sheet.6. REPAIR AND MAINTENANCE
Uncured During Application: Scrape off undesirable texture with a broad knife. Smooth down as much as possible. Let dry and re-apply base coat to repaired area. Once base coat has dried, re-apply desired texture.After Full Cure: If needed, existing texture may be removed using a latex paint stripper. Mask off surrounding areas to be repaired. Apply stripper and allow to soak for 20 minutes. Use a paint scraper to scrape off remover and loosened finish. For stubborn areas, use dry #2 coarse steel wool, sand paper, or a wire brush; and scrub loose. Make necessary repairs to substrate with an appropriate patching compound and materials. Ensure that patched areas are finished so that they are flush with surrounding substrate. Wipe clean with a damp cloth and let dry. Re-apply MT/C base coat to repaired area. Once base has dried, re-apply finish coats in the desired order and texture.
Application:
Base Coat to provide uniform pinhole-free film over entire surface.
Finish Coat applied to desired texture, pursuant to manufacturer's recommendations. Guideline coverage rates as defined in chart. Optional top coats available; consult manufacturer.
| Approximate Coverage Rate sq. ft. per gallon |
Approximate Tip Size |
Approximate Air Pressure |
|||
| MT/C BASE COAT INTERIOR |
150 - 250 | ||||
| EXTERIOR | 100 - 200 | ||||
| MT/C FINISH COAT SPLATTER TEXTURE |
Fine Medium Heavy |
per finish color(coat) 225 175 125 |
single finish color (coat) 150 125 75 |
2-4 mm 4.6 mm 6mm |
40-55 PSI 25-35 PSI 15-25 PSI |
| LACE TEXTURE | Medium Heavy |
175 125 |
100 75 |
4-6 mm 6 mm |
25-35 PSI 15-25 PSI |
| BARK OR CYPRESS TEXTURE (requires knock down application) |
Medium Heavy |
175 125 |
100 75 |
4-6 mm 6 mm |
25-35 PSI 15-25 PSI |
| Optional Top Coats MT/C CLEAR GLAZE |
250-300 | ||||
| Sacrificial Graffiti Guard® | 200-300 | ||||
| Permanent Graffiti Gard® IIIs | Consult Manufacturer | ||||
MTC-TECH-1297